|
How to Program the ICOM- U16 Handheld
NOTICE: TO ALL CONCERNED Certain text files and messages contained on this site deal with activities and devices which would be in violation of various Federal, State, and local laws if actually carried out or constructed. The webmasters of this site do not advocate the breaking of any law. Our text files and message bases are for informational purposes only. We recommend that you contact your local law enforcement officials before undertaking any project based upon any information obtained from this or any other web site. We do not guarantee that any of the information contained on this system is correct, workable, or factual. We are not responsible for, nor do we assume any liability for, damages resulting from the use of any information on this site.
Icom U16 Programming
---------------------------------------------------------------------------
The U16 is made programmable by moving a jumper inside the unit, then try
holding [FUNC] down and entering 159357. You're now in programming mode.
Exit program mode with [FUNC] + [CLR].
Function + 159357 Enter programming mode (Function = [FUNC] key)
Function + [1] PL (CTCSS) Encoder tones (1-37)
+ [2] PL (CTCSS) Decoder tones (1-37)
1= 67.0 2= 71.9 3= 74.4 4= 77.0 5= 79.7
6= 82.5 7= 85.4 8= 88.5 9= 91.5 10= 94.8
11=100.0 12=103.5 13=107.2 14=110.9 15=114.8
16=118.8 17=123.0 18=127.3 19=131.8 20=136.5
21=141.3 22=146.2 23=151.4 24=156.7 25=162.2
26=167.9 27=173.8 28=179.9 29=186.2 30=192.8
31=203.5 32=210.7 33=218.1 34=225.7 35=233.6
36=241.8 37=250.3 (Tone 97.4 Not Available)
+ [3] ?
+ [4] Delta + / Delta - offset, 5 digits
+ [5] Frequency, 5 digits (400MHz +)
+ [6] ?
+ [7] Special Channel Number (allows alias ch.17-99 number)
+ [8] Transmit timeout enable.
+ [9] TI - Transmit Inhibit
+ [SCAN] Priority Scan/Ch Scan
+ [S.CH] Channel Masking
+ [CLEAR] End progamming mode
---------------------------------------------------------------------------
Channel select: Standard method (up/down arrows or CH# + [ENTER])
Frequency: Hold [FUNC], Press [5], enter 6 dig freq, [ENTER], Release
[FUNC]
Rx CTCSS: Hold [FUNC], Press [2], enter 2 dig code, [ENTER], Release
[FUNC]
Tx CTCSS: Hold [FUNC], Press [1], enter 2 dig code, [ENTER], Release
[FUNC]
Offset Freq: Hold [FUNC], Press [4], use [#] for up offset, [*] for
down offset, then enter freq to offset by (ie: [#] [0] [0]
[0] [0] [0] for no offset, [#] [0] [5] [0] [0] [0] for the
standard +5MHz UHF offset), [ENTER], Release [FUNC]
Timeout Timer: Hold [FUNC], [8], Release [FUNC]
Tx Inhibit: Hold [FUNC], [9], Release [FUNC]
Special Ch. #: Hold [FUNC], Press [7], enter the special
channel number (17-99), [ENTER], Release [FUNC]
Data Transfer
MASTER: Hold [FUNC], [BEEP], Release [FUNC]
SLAVE: Hold [FUNC] with power off, turn on, Release [FUNC]
---------------------------------------------------------------------------
-/Vuarnet International/-
617/527.oo91
24oo-16.8k HST/V32bis
|
|
