|
|
 |
|
|
|
register |
bbs |
search |
rss |
faq |
about
|
|
|
meet up |
add to del.icio.us |
digg it
|
|
|
|
Hayes command set
Page 1
Hayes 2400-SmartModem Command Set
=================================
Cmd Settings Meaning
--- -------- -------
ATB ATB0 CCIT format *
1 BELL format
ATE ATE0 Commands not echoed
1 Commands echoed *
ATL ATL0 Speaker volume low
1 Low
2 Medium *
3 High
ATM ATM0 Speaker always off
1 Speaker on except while connected *
2 Speaker always on
3 Speaker on except while connected & dialing
ATQ ATQ0 *
1 Quiet mode
ATV ATV0 Numeric response codes
1 Verbose response codes *
ATX ATX0 SM-300 compatibility mode
1 Extended 'connect' msgs
2 Dialtone detect
3 Busy detect
4 Dialtone and busy detect *
AT&J AT&J0 RJ-11/41/45 jack *
1 RJ-12/13 (A A1 control leads)
AT&L AT&L0 Dialup async/sync *
1 Leased line async/sync
AT&M AT&M0 Async *
1 Sync mode 1 (async call placement)
2 Sync mode 2 (stored number dial DTR)
3 Sync mode 3 (manual dial DTR control)
AT&G AT&G0 No guard tones *
1 550 Hz guard tone
2 1800 Hz guard tone
AT&P AT&P0 US 39%make 61%break pulse dial *
1 UK 33%make 67%break
Page 2
Cmd Settings Meaning
--- -------- -------
ATY ATY0 No long space disconnect *
1 Long space disconnect, recv & xmt
AT&C AT&C0 Carrier detect always on *
1 Carrier detect follows signal
AT&D AT&D0 Ignore DTR *
1 DTR low = command mode (stays online)
2 DTR low = drop connection
3 DTR low = ATZ
AT&R AT&R0 Clear-to-send tracks RTS *
1 CTS for half-duplex transmit
AT&X AT&X0 Transmit clock internal *
1 Clock from DTE pin 15
2 Clock from rcv signal out pin 15
ATA Enter answer mode
A/ Execute last command
ATD T Tone dial
P Pulse dial
R Reverse mode (ans/orig)
W Wait for dialtone
@ Wait for quiet answer
, Pause
! Flash
; Return to command state
S Dial stored number
ATH ATH0 Hang up (on-hook)
1 Pickup line (off-hook)
ATO ATO0 Return online
1 Retrain equalizer & return online
ATZ Reset configuration from stored profile
AT&F Reset configuration from factory settings
AT&W Store active profile
AT&Znn Store one dial number
ATI ATI0 Show product code
1 Show checksum
2 Verify checksum
Page 3
Cmd Settings Meaning
--- -------- -------
AT&T AT&T0 Terminate any test
1 Local analog loopback
3 Local digital loopback
4 Allow a remote digital loopback request
5 Prohibit remote digital loopback request
6 Initiate remote digital loopback
7 Initiate remote digital loopback with selftest
8 Initiate local analog loopback with selftest
Register 0 0-255 rings 00 Ring to answer on
1 0-255 rings Ring count
2 0-127 ascii 43 Escape code char
3 0-127 ascii 13 Carriage return char
4 0-127 ascii 10 Line feed
5 0-127 ascii 08 Backspace char
6 0-255 seconds 02 Wait for dialtone
7 1-30 seconds 30 Wait for carrier
8 0-255 seconds 02 Pause time comma
9 1-255 .1 sec 06 Carr detect response
10 1-255 .1 sec 14 Lost carrier hangup
11
12 0-255 .02 sec 50 Escape guard time
13
14 none Options register
15
16 none 00 Modem test options
17
18 0-255 seconds 00 Test timer
19
20
21 none Options register
22 none 76'x Options register
23 none 07 Options register
24
25 0-255 seconds 05 Sync delay to DTR
26 0-255 seconds 00 RTS/CTS delay HD
27 none 00 Options register
Page 4
Result 0 OK Acknowledge execution
Codes 1 CONNECT 0-300 bps connection
2 RING Ring detected
3 NO CARRIER No connect or lost
4 ERROR Error
5 CONNECT 1200 1200 bps connection
6 NO DIALTONE No dialtone found
7 BUSY Busy signal
8 NO ANSWER @, no quiet answer
9 CONNECT 0600 600 bps connection
10 CONNECT 2400 2400 bps connection
|
|
|
To the best of our knowledge, the text on this page may be freely reproduced and distributed.
If you have any questions about this, please check out our Copyright Policy.
totse.com certificate signatures
|
|
|
About | Advertise | Bad Ideas | Community | Contact Us | Copyright Policy | Drugs | Ego | Erotica
FAQ | Fringe | Link to totse.com | Search | Society | Submissions | Technology
|
|
|
|
|
|
