About
Community
Bad Ideas
Drugs
Ego
Erotica
Fringe
Society
Technology
Phreak
Boxes, Old and New
Bugs and Taps
Cellular Phones
Introduction to Telecommunications
PBX's and Switches
Payphones
Phone Phun
VMB's, Pagers, E-Mail, and S&F Systems
register | bbs | search | rss | faq | about
meet up | add to del.icio.us | digg it

Cell phone programming info for 30+ phones


NOTICE: TO ALL CONCERNED Certain text files and messages contained on this site deal with activities and devices which would be in violation of various Federal, State, and local laws if actually carried out or constructed. The webmasters of this site do not advocate the breaking of any law. Our text files and message bases are for informational purposes only. We recommend that you contact your local law enforcement officials before undertaking any project based upon any information obtained from this or any other web site. We do not guarantee that any of the information contained on this system is correct, workable, or factual. We are not responsible for, nor do we assume any liability for, damages resulting from the use of any information on this site.
NAM Programming (Reprogramming) Instructions

For 30+ Cellular Telephones

<--Part 1-->

Presented By:

/E/D/I/S/O/N///C/A/R/T/E/R/

Of

NETWORK 23
24 HOURS
1200/2400 BAUD
(402) 467-2474

-----------------------------------------------------------------------------
PLEASE NOTE: Area specific numbers contained within these programming
instructions may not be accurate for your cellular area.
-----------------------------------------------------------------------------

Programming Instructions for:

DIAMONDTEL MESA90X HANDHELD

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
PRESS FCN 7
ENTER 4 DIGIT SECURITY CODE
ENTER NEW 3 DIGIT UNLOCK CODE
PRESS CLR

PWR up unit
Press "END" and hold within 10 seconds of pwr up
Enter "5132920"
Release END key.

0 SEND DUAL NO

XXXXXXXXXX SEND NO1

_ _ _ _ _ SEND SID1

1 SEND LU1

1 SEND EX1

334 SEND IPCH1

07 SEND ACCOLC1

0 SEND PREF1

10 SEND GIM1

0 SEND RI1

1 SEND DTX1

1 SEND AR1

1234 SEND SEC

1 SEND EE

1 SEND C TONE

0 SEND AL

0 SEND BO

1 SEND BEEP

TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME

TO RESET NAM FROM THE LIMIT OF 3 PROGRAM ATTEMPTS
PWR up unit
Press "END" and hold within 10 seconds of pwr up
TO RESET NAM OF MESA 90 HANDHELD USE THE CODE "6972814"



Programming Instructions for:

DIAMONDTEL MESA99X HANDHELD

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
PRESS FCN 7
ENTER 4 DIGIT SECURITY CODE
ENTER NEW 3 DIGIT UNLOCK CODE
PRESS CLR

PWR up unit
Press "END" and hold within 10 seconds of pwr up
Enter "5132920"
Release END key.

0 SEND DUAL NO

XXXXXXXXXX SEND NO1

_ _ _ _ _ SEND SID1

1 SEND LU1

1 SEND MIN MARK1

334 SEND IPCH1

07 SEND ACCOLC1

10 SEND GIM1

0 SEND RI1

0 SEND DTX1

0 SEND AR1

1234 SEND SEC

1 SEND CONTINUE D.T.M.F.

0 SEND AUTO LOCK

0 SEND BOOSTER

TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME



Programming Instructions for:

GATEWAY CP 900 HANDHELD

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
CURRENT UNLOCK CODE CAN NOT BE SEEN AND MUST BE KNOWN TO CHANGE
THE CURRENT UNLOCK CODE.
PRESS MENU
ENTER 03
ENTER CURRENT 4 DIGIT SECURITY CODE
ENTER NEW 4 DIGIT SECURITY CODE
PHONE WILL AUTO EXIT TO READY

ACTION TO STORE DISPLAY

PRESS MENU 99 ENTR SCRTY CODE(FCTRY PRST IS 9999) PROGRAM NAM

_ _ _ _ _ SEND SID

XXXXXXXXXX SEND PHONE NUMBER

0334 SEND IPC

07 SEND ACCOL

10 SEND GIM

1 SEND MOBILE I.D. NUMBER

1 SEND LOCAL USE MARK

2 SEND SYSTEM SELECT (B)

UPON PRESSING SEND THE PHONE WILL CYCLE TO WAIT AND THEN RETURN TO THE
READY MODE.

TO DISPLAY THE NEW PHONE NUMBER:

PRESS RCL 00



Programming Instructions for:

GENERAL ELECTRIC MINI II

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
PRESS FCN 7
ENTER 4 DIGIT SECURITY CODE
ENTER NEW 3 DIGIT UNLOCK CODE
PRESS CLR

PWR up unit
Press and hold END key within 10 seconds of pwr up
Enter "6282905"
Release END key

0 Press SEND DUAL NO

XXXXXXXXXX Press SEND NO1

_ _ _ _ _ Press SEND SID1

1 Press SEND LU1

1 Press SEND EX1

0334 Press SEND IPCH1

07 Press SEND ACCOLC1

0 Press SEND PREF1

10 Press SEND GIM1

0 Press SEND RI1

1 Press SEND DTX1

1 Press SEND AR1

1234 Press SEND SEC

1 Press SEND EE

1 Press SEND C DTMF

0 Press SEND AL

0 Press SEND BEEP

0 Press SEND BO

TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME



Programming Instructions for:

GENERAL ELECTRIC MINI

ACTION TO STORE DISPLAY
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
UNLOCK CODES WILL BE CHANGED ONLY IN PROGRAMMING MODE
FOLLOW THE INSTRUCTIONS THAT FOLLOW

PWR up unit
Press and hold CL key within 10 seconds of pwr up
0Enter "7591122"
Release CL key

XXXXXXXXXX PRESS SEND MIN

123 PRESS SEND UNLOCK

_ _ _ _ _ PRESS SEND SID

1 PRESS SEND LU

1 PRESS SEND MIN MARK

334 PRESS SEND IPCH

07 PRESS SEND ACCOLC

0 PRESS SEND PS

10 PRESS SEND GIM

1 PRESS SEND EE
0 PRESS SEND BOOSTER

1 PRESS SEND AR

TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME



Programming Instructions for:

MITSUBISHI 800

ACTION TO STORE DISPLAY

PWR up unit
Press and Hold STO within 10 Seconds of pwr up
Enter "5474432"
Release STO

0 Press SEND dUAL

XXXXXXXXXX Press SEND NO1

_ _ _ _ _ Press SEND SId1

1 Press SEND LU1

0 Press SEND MIN Mark

0334 Press SEND IPCH

07 Press SEND ACCOLC

0 Press SEND PS1

10 Press SEND GI1

1234 Press SEND SECUrity

1 Press SEND EE

0 Press SEND dt

1 Press SEND HF

0 Press SEND InHIbit

1 Press SEND C tOnE

0 Press SEND SyS A/B

0 Press SEND dUAL HS

0 Press SEND InHibit Ld

TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME



Programming Instructions for:

MITSUBISHI 900

ACTION TO STORE DISPLAY

PWR up unit
Press and Hold END key within 10 seconds of pwr up
Enter "6972814"
Release END key

0 Press SEND DUAL NO

XXXXXXXXXX Press SEND NO1

_ _ _ _ _ Press SEND SID1

1 Press SEND LU1

0 Press SEND EX1

0334 Press SEND IPCH1

07 Press SEND ACCOLC1

0 Press SEND PREF1

10 Press SEND GIM1

0 Press SEND RI1

1 Press SEND DTX1

1 Press SEND AR1

1234 Press SEND SEC

1 Press SEND EE

1 Press SEND C DTMF

0 Press SEND AL

0 Press SEND BO

1 Press SEND BEEP

TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME

TO ENTER TEST MODE HOLD END ON PWR UP-CODE 0944635



Programming Instructions for:

MOTOROLA 8000H

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
THIS FUNCTION IS PROVIDED IN STEP 9 OF THE PROGRAMMING
MODE

PWR up unit
Enter STORE #123456123456 RCL
If the phone is fresh from factory then
Enter STORE #000000000000 RCL
If the phone is used or already programmed then
Enter STORE #123456123456 RCL

DISPLAY WILL SHOW 01
PRESS *

_ _ _ _ _ * 02 (SID)

XXX * 03 (Area Code)

XXX XXXX * 04 (Phone #)

14 * 05

07 * 06

00 * 07

123456 * 08

123 * 09

334 * 10

010100 * 11

000 *

PRESS * TO REVIEW ENTRIES

TO BURN NAM: PRESS SEND WHILE 01,02,03, ETC. IS DISPLAYED

SET TO SCAN B MODE BY :

RCL * : PRESS * UNTIL SCAN B MODE SHOWS then:

press store



Programming Instructions for:

MOTOROLA ULTRA CLASSIC HANDHELD

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
THE UNLOCK CODE IS PROGRAMMED IN STEP 8 OF THE PROGRAMMING
MODE

FOR NEW PHONE: Press FCN, 0 + Security code entered twice (Factory
preset is 000000), RCL

The message 01 will appear in the display to confirm programming mode.

Press * 01 Press *

1) _ _ _ _ _ Press * 02 Press *

2) XXX Press * 03 Press *

3) XXX XXXX Press * 04 Press *

4) 14 Press * 05 Press *

5) 07 Press * 06 Press *

6) 10 Press * 07 Press *

7) 123456 Press * 08 Press *

8) 123 Press * 09 Press *

9) 0334 Press * 10 Press *

10) 010101 Press * 11 Press *

11) 101 Press * 12 Press *

Review entries by pressing "*" repeatedly.

Press SEND to program phone.



Programming Instructions for:

NEC P300

ACTION TO STORE DISPLAY

THESE INSTRUCTIONS FOR SERIAL NUMBERS AFTER 135-839601

Insert NAM Programming Adapter (NECAM #41-2019) into plug connector on P300
phone bottom.

PWR On

RCL # 0 1 to enter test mode. Phone will display shaded blocks.

RCL # 7 6 to select NAM. Phone will show 76-
Press 0 # to program NAM 1. (NAM 1=0,NAM 2=1,NAM 3=2,NAM 4=3)

RCL # 7 1 to enter programming mode.

XXXXXXXXXX PRESS # MIN

1234 PRESS # LOCK CODE

_ _ _ _ _ PRESS # SID

10 PRESS # GROUP I.D.

0334 PRESS # INITIAL PAGING CH

0 PRESS # SYSTEM SELECT (1=A)

07 PRESS # ACCOLC

1 PRESS # MIN MARK 1

1 PRESS # LOCAL USE

911 PRESS # EMERGENCY NO.

Press Clr (and hold) to exit programming and return to TEST MODE.

Press RCL # 0 2 to burn and exit to standby.


THESE INSTRUCTIONS FOR SERIAL NUMBERS PRIOR TO 135-839601

Insert NAM Programming Cable (41-2019)
PWR on
RCL # 7 6 to enter TEST MODE
Press 0 # to select NAM.
RCL # 7 1
You are now in Programming Mode.
Enter NAM info as above.
Press and hold CLR to exit.
Pwr down.



Programming Instructions for:

NEC P9100

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
UNLOCK CODES WILL BE CHANGED ONLY IN PROGRAMMING MODE
FOLLOW THE INSTRUCTIONS THAT FOLLOW


Make sure NAM battery is fully charged before attempting programming
Switch power on
Press RCL #01 display will then show shaded blocks

For a USED phone - to clear nam and accumulated call timer
Press RCL #39

To program NAM1
Press RCL #760#
To enter programming mode Press RCL #71

XXXXXXXXXX Press # MIN

1234 Press # Lock Code

_ _ _ _ _ Press # SYS. I.D.

10 Press # G.I. Mark

0334 Press # First Paging Channel

0 Press # System Select

07 Press # ACCOLC

0 Press # MIN Mark

1 Press # Local Use

TO EXIT PROGRAM MODE AT THIS TIME PRESS CLR AND HOLD
DISPLAY WILL SHOW TEST MODE

TO EXIT TEXT MODE PRESS RCL#02

IF THE MEMORY IS CLEARED VIA RCL #39 DURING THE PROGRAMMING THEN THE PHONE
WILL AUTOMATICALLY ENTER FULL-LOCK AFTER EXITING THE TEST MODE
TO UNLOCK: FCN #XXXX(4 DIGIT LOCK CODE FOR LAST NAM PROGRAMMED).



Programming Instructions for:

NOKIA P-30

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
PRESS SEL 7 UNLCODE APPEARS ON THE DISPLAY
ENTER 5 DIGIT SECURITY CODE AND THE CURRENT UNLOCK CODE APPEARS IN
THE DISPLAY PRESS CLR AND ENTER THE NEW FOUR DIGIT UNLOCK CODE
PRESS SEL TO STORE THE NEW CODE - NOTE: IF YOU DON'T PRESS SEL WITHIN
FIVE SECONDS THE DISPLAY WILL CLEAR AND CANCEL THE FUNCTION

PWR up unit
Enter *17*2001*12345*
HO-Id must appear on display
Press SEL to view current value
Display will be one step behind TO STORE instructions

_ _ _ _ _ Press SEL ACCESS (SID)

1 Press SEL LOCAL

1 Press SEL PhonE n

XXXXXXXXXX Press SEL CLASS

10 Press SEL PAGE ch

334 Press SEL O-LOAd

07 Press SEL GrouP

10 Press SEL SEC

12345 Press SEL AUTO EXIT PROGRAM MODE

TO EXIT PROGRAMMING MODE AT ANY TIME PRESS "END"

WHEN THE SEL KEY IS PRESSED FOLLOWING THE LAST PARAMETER VALUE, THE PHONE
WILL AUTOMATICALLY EXIT THE NAM PROGRAMMING MODE AND RETURN TO NORMAL
OPERATION



Programming Instructions for:

NOVATEL PTR800


ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
UNLOCK CODES WILL BE CHANGED ONLY IN PROGRAMMING MODE
FOLLOW THE INSTRUCTIONS THAT FOLLOW

PWR up unit
Press FCN
Press FCN again
Enter *626776*
Display will show CMT REV and a date code - Press Volume Up
Display will show NAM SELECT1 Press Volume Up

_ _ _ _ _ PRESS # PRESS VOLUME UP SIDH
PRESS VOLUME UP SCM
XXXXXXXXXX PRESS # PRESS VOLUME UP MIN
0333 PRESS # PRESS VOLUME UP IDCCA
0334 PRESS # PRESS VOLUME UP IDCCB
0334 PRESS # PRESS VOLUME UP IPCH
07 PRESS # PRESS VOLUME UP ACCOLC
10 PRESS # PRESS VOLUME UP GIM
123 PRESS # PRESS VOLUME UP LOCK A
456 PRESS # PRESS VOLUME UP LOCK B
1 PRESS # PRESS VOLUME UP OPTION LC
1 PRESS # PRESS VOLUME UP OPTION EX
0 PRESS # PRESS VOLUME UP OPTION PS
0 PRESS # PRESS VOLUME UP OPTION NSC
1 PRESS # PRESS VOLUME UP OPTION EE
1 PRESS # PRESS VOLUME UP OPTION REP
0 PRESS # PRESS VOLUME UP OPTION HA
0 PRESS # PRESS VOLUME UP OPTION HF
0 PRESS # PRESS VOLUME UP OPTION F1
0 PRESS # PRESS VOLUME UP OPTION F2
0 PRESS # PRESS VOLUME UP OPTION F3
0 PRESS # PRESS VOLUME UP OPTION F4

TO EXIT PROGRAMMING MODE AT ANY TIME PRESS FCN END

FCN FCN *6462257* WILL CLEAR THE NAM IF IT HAS BEEN PROGRAMMED MORE THAN
3 TIMES OR IF THE NEED EXISTS TO CLEAR THE MEMORY



Programming Instructions for:

NOVATEL PTR825

ACTION TO STORE DISPLAY
PWR up unit
Press FCN
Press FCN again
Enter *697201*
Display will show CMT REV 972 105 Press Volume Up

1 PRESS # VOL UP NAM SELECT 1
_ _ _ _ _ PRESS # VOL UP SIDH
10 PRESS VOL UP SCM
XXXXXXXXXX PRESS # VOL UP MIN
0333 PRESS VOL UP IDCCA
0334 PRESS VOL UP IDCCB
0334 PRESS # VOL UP IPCH
07 PRESS # VOL UP ACCOLC
10 PRESS # VOL UP GIM
123 PRESS # VOL UP LOCK A
123 PRESS # VOL UP LOCK B
1 PRESS # VOL UP LC
1 PRESS # VOL UP OPTION EX
0 PRESS # VOL UP PS - PREF SYSTEM
0 PRESS VOL UP OPTION NSC
1 PRESS # VOL UP OPTION EE-END TO END
1 PRESS # VOL UP OPTION REP
0 PRESS # VOL UP HORN ALERT
0 PRESS # VOL UP HANDS FREE
0 PRESS # VOL UP OPTION F1
0 PRESS # VOL UP OPTION F2
0 PRESS # VOL UP OPTION F3
1 PRESS # VOL UP OPTION F4 AIR RND UP
0 PRESS # VOL UP OPTION F5 FUTURE USE
0 PRESS # VOL UP OPTION F6 FUTURE USE
0 PRESS # VOL UP OPTION F7 FUTURE USE


Programming will now wrap to beginning SIDH display.
Press VOL UP to review entries



Programming Instructions for:

OKI HANDHELD MODEL # 750

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
THIS FUNCTION IS PROVIDED FOR IN THE PROGRAMMING SEQUENCE



Pwr up unit
Press (*) and (#) simultaneously
Enter 10 digit Sec Code as follows: *12345678#
What follows can be done only once!

The display "Enter NEW PW-Sto"
Enter 0123456789 then press STORE

Pwr unit down.

Pwr up unit
Press MENU and RCL simultaneously
Enter 0123456789 Software Version and
ESN Number in HEX

Clears in 2 secs.

Spd Dial Mem Clear

Press 0 Press STO Def Data Reset

Press 0 Press STO

NAM 1 Mode

Own #111 111-1111

XXX XXX XXXX Press STO Vol Up Security

123456 Press STO Vol Up OPTION

1100 Press STO Vol Up SCM

1010 Press STO Vol Up GIM

10 Press STO Vol Up Unlock #

1234 Press STO Vol Up ACCOLC #

07 Press STO Vol Up IPCH NO.

0334 Press STO Vol Up

_ _ _ _ _ Press STO Vol Up System ID:

At this time you may exit the programming mode by pressing CLR to bypass
the other NAM modules.



Programming Instructions for:

OKI HANDHELD MODEL # 900

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
THIS FUNCTION IS PROVIDED FOR IN THE PROGRAMMING SEQUENCE

Pwr up unit
Press RCL and MENU simultaneously
Enter 10 digit Sec Code as follows: *12345678#
What follows can be done only once!

The display "Enter NEW PW-Sto"
Enter 0123456789 then press STORE.
The display "Re-Enter New PW-Sto"
Enter 0123456789 then press STORE to enter Programming Mode.
IF You don't wish to keep the new password then Pwr unit down.

Software Version and
ESN Number in HEX

Clears in 2 secs.

Spd Dial Mem Clear

Press * Press STO SPD DIAL MEM CLEAR

Press * Press STO DEFAULT DATA CLEAR

NAM 1 Mode

Own #111 111-1111

XXX XXX XXXX Press STO Vol Up MIN

123456 Press STO Vol Up SECURITY

_ _ _ _ _ Press STO Vol Up SYSTEM ID:

0334 Press STO Vol Up IPCH

07 Press STO Vol Up ACCOLC #

15 Press STO Vol Up GROUP I.D.

1234 Press STO Vol Up UNLOCK CODE

1010 Press STO Vol Up STATION CLASS

1110 Press STO Vol Up OPTION


At this time you may exit the programming mode by pressing CLR to bypass
the other NAM modules.



Programming Instructions for:

PANASONIC EB3500


Charged Battery and Nam Adaptor are needed.

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
THIS FUNCTION IS PROVIDED FOR IN THE PROGRAMMING SEQUENCE



*0000# to enter program mode

*1 Press SND NAM 1 MODE

_ _ _ _ _ Press STO 01 SIDH

XXXXXXXXXX Press STO 02 OWNDL

0 Press STO 03 PRESYS

334 Press STO 04 IPCH

07 Press STO 05 ACCOLC

10 Press STO 06 GIM

00 Press STO 07 DLMT

10 Press STO 08 SCM

911 Press STO 09 SPDL

1234 Press STO 10 LOCK

1 1 0 1 1 0 0 0 Press STO 11 FCN 1

0 0 0 1 0 1 0 0 Press STO 12 FCN 2

1 1 1 1 0 1 1 1 Press STO 13 FCN 3

STO **
END to program phone



Programming Instructions for:

COLT TRANSPORTABLE

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
UNLOCK CODES WILL BE CHANGED ONLY IN PROGRAMMING MODE
FOLLOW THE INSTRUCTIONS THAT FOLLOW

Phone must be locked, to accomplish: press FUNC 5
Enter: FUNC #626# FUNC
The software revision date will be shown.
Press SEND
This will advance phone through memory locations.
E.S.N. will be displayed, press SEND again.

XXX Press SEND AREA CODE

XXX XXXX Press SEND PHONE NUMBER

_ _ _ _ _ Press SEND SYSTEM ID

07 Press SEND ACCOLC

10 Press SEND GIM

1 Press SEND LOCAL USE MARK

1 Press SEND MIN MARK (MOBILE ID)

123 Press SEND LOCK CODE

0 Press SEND AUTOMATIC LOCK

123 Press SEND CALL RESTRICTION

12 Press SEND CALL COUNTER RESET

1 Press SEND ENABLE HANDSFREE

0 Press SEND DISABLE HORN ALERT

0 Press SEND HA TURN OFF TIME

12 Press SEND TOTAL AIRTIME RESET

TO REVIEW PROGRAMMING AT THIS TIME PRESS SEND.

TO EXIT PROGRAMMING AND STORE DATA AT ANY TIME PRESS
END FUNC END - WAKE UP WILL SOUND, PHONE WILL BE LOCKED
ENTER UNLOCK CODE- 123

SYSTEM PREFERENCE MUST BE KEYPAD SELECTED! PRESS FUNC 7 FOR "A" NON W/L

OR PRESS FUNC 8 FOR "B" W/L SYS.



Programming Instructions for:

DIAMONDTEL MESA 55 TRANSPORTABLE

ACTION TO STORE DISPLAY

PWR up unit
Press "CL" and hold within 10 seconds of pwr up
Enter "1951426"
Current Mobile I.D. will display

XXXXXXXXXX Press SEND MIN

123 Press SEND 1 SECURITY

_ _ _ _ _ Press SEND 2 SID

1 Press SEND 3 LU

1 Press SEND 4 MIN MARK

334 Press SEND 5 IPCH

07 Press SEND 6 ACCOLC

0 Press SEND 7 PREF SYS

10 Press SEND 8 GIM

1 Press SEND 9 EE

1 Press SEND 10 ENBL HANDSFREE

0 Press SEND 11 RI

04 Press SEND 12 AUX 1

07 Press SEND 13 AUX 2

Phone automatically returns to show the 10 digits MIN number at this time
and to indicate that the NAM has been programmed. The END key should be
pressed to burn the NAM.



Programming Instructions for:

DIAMONDTEL MESA95 TRANSPORTABLE

ACTION TO STORE DISPLAY

PWR up unit
Press and hold Clr within 10 Seconds of pwr up
Enter "1951426"
Release Clr

0 Press SEND duaAL no

XXXXXXXXXX Press SEND no1

_ _ _ _ _ Press SEND SId1

1 Press SEND LU1

1 Press SEND E1

334 Press SEND IPCH1

07 Press SEND ACCOLC1

0 Press SEND PS1

10 Press SEND GI1

5 Press SEND t InC1

1234 Press SEND SECUrIty

1 Press SEND EE

0 Press SEND dt

0 Press SEND HF

0 Press SEND InHIbIt

1 Press SEND Ctone

0 Press SEND dIS CU

0 Press SEND dIS IGn
SEnSE

0 Press SEND DUAL HS

TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME

TO RESET NAM FROM THE LIMIT OF 3 PROGRAM ATTEMPTS
FOLLOW THE BLOCK OF INSTRUCTIONS AT TOP USING "8291112" W/CLR

TO RESET NAM OF MESA 90 HANDHELD USE THE CODE "6972814"



Programming Instructions for:

FUJITSU MOBILE PHONE

ACTION TO STORE DISPLAY

PWR up unit
Unit must be locked to program.
To lock press F+LOCK
PWR down unit.
PWR up unit.
Within 10 seconds press #626#7764726 (#NAM#PROGRAM)
A continuous tone will be heard for 7 seconds.
PRESS AND HOLD THE * KEY WHILE THE TONE SOUNDS,
DO NOT LET GO!
The tone will change to an intermittent tone, then it will stop.
Release the * key.

CONGRATULATIONS!!! YOU ARE NOW IN PROGRAMMING MODE!

_ _ _ _ _ PRESS STOR 1 SIDH

1 PRESS STOR 2 LOCAL

1 PRESS STOR 3 MIN MARK

XXXXXXXXXX PRESS STOR 4 MIN

10 PRESS STOR 5 STATION

0334 PRESS STOR 6 IPCH

07 PRESS STOR 7 ACCOLC

0 PRESS STOR 8 PS

10 PRESS STOR 9 GIM

1234 PRESS STOR 10 LOCK

1 PRESS STOR 11 CALL TIME

2 PRESS STOR 12 AUTO LOCK

1 PRESS STOR 13 CALL REST

PRESS STOR TO REVIEW ENTRIES.
WHEN AT MODE #1 PRESS SEND TO BURN NAM AND RETURN TO NORMAL OPERATION.

IF PROGRAMMING WAS DONE INCORRECTLY A SHORT HIGH TONE WILL BE HEARD, YOU
MUST THEN REPEAT DATA ENTRY. YOU MUST PRESS STOR AFTER EACH ENTRY FOR THE
CHECKSUM FUNCTION TO BE FULFILLED.



Programming Instructions for:

GENERAL ELECTRIC CARFONE XR3000

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
THE UNLOCK CODE IS PROGRAMMED IN STEP 2 OF THE PROGRAMMING
MODE


PWR up unit
Press "CL" and hold within 10 seconds of pwr up
Enter "923885"
Serial # will display
Press Send key to advance to first entry

XXXXXXXXXX Press SEND MIN

123 Press SEND UNLOCK

_ _ _ _ _ Press SEND SID

1 Press SEND LU

1 Press SEND MIN MARK

334 Press SEND IPCH

07 Press SEND ACCOLC

0 Press SEND PS

10 Press SEND GIM

0 Press SEND AUX

1 Press SEND HANDS

PRESS SEND TO REVIEW ENTRIES. NOTE: AREA CODE (402) WILL DISPLAY FOR MIN
THEN AUTO SWITCH TO REST OF NUMBER ON DISPLAY - BE PATIENT

PRESS "E" KEY TO COMPLETE PROGRAMMING OF THE XR 3000 AT THIS TIME



Programming Instructions for:

GOLDSTAR SERIES 5000 MOBILE

ACTION TO STORE DISPLAY

PWR up Unit
Press FCN 4 to see the selected NAM. Press * to advance. Select NAM1.
Press FCN, 9, 9, * "Enter Code" will be displayed.
Enter 1234567890

XXXXXXXXXX PRESS MEM Enter MIN

_ _ _ _ _ PRESS MEM Enter System ID

0334 PRESS MEM Enter IPCH

07 (ACCOLC) PRESS MEM Enter OVLD Class

1234 PRESS MEM LOCK CODE

123456 PRESS MEM SECURITY CODE

1234 PRESS MEM ALARM DISARM CODE

0 PRESS MEM PREFFERED SYSTEM

0 PRESS MEM STATION CLASS MARK

1 PRESS MEM HANDS FREE MARK (ON)

1 PRESS MEM LOCAL USE MARK (ON)

1 PRESS MEM MIN MARK (ON)

0 PRESS MEM HORN ALERT (OFF)

0 PRESS MEM OPT. SPEAKER (OFF)

TO SAVE TO NAM NOW PRESS MEM

TO REVIEW ENTRIES USE THE VOLUME UP OR DOWN KEYS



Programming Instructions for:

MITSUBISHI 555,560,600

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
TO PROGRAM THIS FUNCTION YOU MUST BE OUT OF THE PROGRAMMING MODE
ENTER FCN 6 AND THEN ENTER THE NEW 3 DIGIT UNLOCK CODE
PRESS CLR.

To program from keypad remove and discard Nam Pad
PWR up unit
Press and Hold STO key within 10 seconds of pwr up
Enter "5474432"
Release STO key

XXXXXXXXXX Press SEND MIN

123 Press SEND SECURITY CODE

_ _ _ _ _ Press SEND SID

1 Press SEND LU

1 Press SEND MIN MARK

334 Press SEND IPCH1

07 Press SEND ACCOLC1

0 Press SEND PS1

10 Press SEND GIM

1 Press SEND EE

1 Press SEND HANDS FREE

0 Press SEND ROAM INHIBIT

0 Press SEND A/B SELECT

00 Press SEND f3-f0 DUAL HEAD

00 Press SEND f7-f4 LD INH

TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME

Installing the LOCK CODE

To program the customer's lock code, the phone must be out ot the
programming mode.
To program, enter FCN, 6,3-digit security code, the a 3-digit lock code.
Press CLR.



Programming Instructions for:
NEC M3700 SERIES MOBILE

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
UNLOCK CODES WILL BE CHANGED ONLY IN PROGRAMMING MODE
FOLLOW THE INSTRUCTIONS THAT FOLLOW

A NAM PROGRAMMER ADAPTOR (NECAM #41-2012) IS
REQUIRED

PWR UP

TO ENTER TEST MODE:

RCL, #,0,1. WILL CYCLE TO SHADED

TO CLEAR MEMORY:

RCL # 3 9
select nam
RCL # 7 6 0 # nam 1
RCL # 7 6 1 # nam 2

TO ENTER PROGRAMMING MODE:

RCL #71

XXX XXX XXXX PRESS # Telephone No. (MIN)

1234 PRESS # Lock Code

_ _ _ _ _ PRESS # Home Area (SYS I.D.)

10 PRESS # G-NO (Group I.D.)

0334 PRESS # First Paging Channel

0 for wireline PRESS # System Select

07 PRESS # ACCOLC

1 PRESS # ACCESS

1 PRESS # Local Use

To exit PROGRAMMING MODE PRESS CLR and hold TEST MODE will show

to exit TEST MODE RCL #02

IF MEM WAS CLEARED VIA RCL #39, PHONE WILL AUTOMATICALLY ENTER FULL-LOCK
AFTER EXITING THE TEST MODE.
TO UNLOCK PRESS FCN # 1234.



Programming Instructions for:

NOKIA LX-11

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
PRESS SEL,5 THEN ENTER 5 DIGIT SECURITY CODE
PRESS SEL TO RECEIVE DISPLAY OF CURRENT UNLOCK CODE
PRESS 5 NOW TO CLEAR ALL CALL TIMERS
ENTER THE NEW UNLOCK CODE
PRESS SEL TO ACCEPT

PWR up unit
Enter *3001#12345 Then - SEL 9 END
IdEnt IF InFO should appear on display

Pressing END will move you through the parameters
Pressing SND will toggle between choices available

_ _ _ _ _ Press END HO-Id (SID)

1 Press END ACCESS

1 Press END LOCL OPt

XXXXXXXXXX Press END Phonxx

08 Press END St CLASS

334 Press END PAging Ch

07 Press END O-LOAd CLASS

B Press END PrEF SyS

10 Press END grOUP Id

12345 Press END SECUrIty

-------- (Can't be changed) Press END 1 dAtE

00/00/90 (INSTALLATION DATE) Press END 2 dAtE

TO EXIT PROGRAMMING MODE AT ANY TIME PRESS "END" TO STORE LAST PARAMETER
THEN POWER DOWN
WHEN THE "END" KEY IS PRESSED FOLLOWING THE LAST PARAMETER, THE TEXT
Prog donE WILL APPEAR ON DISPLAY



Programming Instructions for:

NOKIA M-10

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
THIS FUNCTION IS PROVIDED BY THE SECURITY CODE PROGRAMMED AT THE
TIME OF PROGRAMMING


PWR up unit
Enter *17*3001*1234*
HO-Id must appear on display
Press SEL to view current value
Display will be one step behind TO STORE instructions

_ _ _ _ _ Press SEL ACCESS (SID)

1 Press SEL LOCAL

1 Press SEL PhonE n

XXXXXXXXXX Press SEL CLASS

08 Press SEL PAGE ch

334 Press SEL O-LOAd

07 Press SEL GrouP

10 Press SEL SEC

1234 Press SEL AUTO EXIT PROGRAM MODE

TO EXIT PROGRAMMING MODE AT ANY TIME PRESS "END"

WHEN THE SEL KEY IS PRESSED FOLLOWING THE LAST PARAMETER VALUE, THE PHONE
WILL AUTOMATICALLY EXIT THE NAM PROGRAMMING MODE AND RETURN TO NORMAL
OPERATION



Programming Instructions for:

NOVATEL 8305 TRANSPORTABLE

CA08 SOFTWARE VERSION

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
IF EQUIPMENT IS PROVIDED WITH A MENU KEY THEN ENTER THE MENU PORTION OF
THE PHONE AND DISPLAY AND IF NECESSARY REPROGRAM THE UNLOCK CODE FROM
THERE.
IF PHONE DOES NOT HAVE A MENU KEY THEN THERE CAN BE NO PROGRAMMING OF THE
UNLOCK CODE... THE SECURITY CODE WILL BE ALL THAT IS PROVIDED

Lock Phone by pressing FCN 1
Enter Programming Mode by pressing #259

Screen will display the software revision number
Press Volume Up

Screen will display Phone's E.S.N.
Press Volume Up

Screen will display INIT REP USE SND
Press SEND to erase any numbers stored in the phones memory
Press Volume Up

_ _ _ _ _ Send Vol. Up SIDH system I.D.

XXX XXX XXXX Send Vol. Up MIN mobile I.D.

Must be changed when done Send Vol. Up LOCK CODE 1
programming - BY CUSTOMER
Must be changed when done Send Vol. Up LOCK CODE 2
programming - BY CUSTOMER
SET Vol. Up Option EX extnd adrss
334 press send to change Vol. Up IPCH initial pge
07 Send Vol. Up ACCOLC overload
10 Send Vol. Up GIM group i.d.
333 Vol. Up IDCCA initl a
334 Vol. Up IDCCB initl b
1 Vol. Up REG TBL SIZE
Volume up through the four invalid System I.D. addresses
SET Vol. Up OPTION LU local use
B press send to change Vol. Up OPTION PS (prefered sys)
CLR Vol. Up OPTION IRI rm inhbt
CLR Vol. Up OPTION SSD
SET Vol. Up OPTION QRC qck rcall
SET Vol. Up OPTION QST qck store
SET Vol. Up OPTION WUT wake tone
SET Vol. Up OPTION EE use dtmf
SET Vol. Up OPTION FD use dtmf
SET Vol. Up OPTION MFD ext dtmf
SET Vol. Up OPTION 32D dgt dial
CLR Vol. Up OPTION MLH timer
CLR Vol. Up OPTION LHM timer
CLR Vol. Up OPTION CRU timer dsp
CLR Vol. Up OPTION NLM timer
SET for on CLR for off Vol. Up OPTION HA hrn alert
CLR Vol. Up OPTION ONL diagnostc
END to exit or VOLUME UP to review entries.



Programming Instructions for:

OKI CDL400

ACTION TO STORE DISPLAY

To Enter Programming mode:

Press IN SEQUENCE:
END RCL FUNC CLR SND

Screen shows Entr id

Enter 08693427

XXX XXX XXXX PRESS # PRESS * PHon

_ _ _ _ _ PRESS # PRESS * S id no

0334 PRESS # PRESS * iPCH

07 PRESS # PRESS * ACC oLC

123 PRESS # PRESS * LoC Cod

10 PRESS # PRESS * G id

0000 PRESS # PRESS * Stn CLS

0111 PRESS # PRESS * HORN ALERT, HANDS
FREE, LOCAL USE,
MIN. MARK.

PRESS END AT THIS TIME TO EXIT PROGRAMMING MODE.

__________________________________________________________________________

TO REPROGRAM TELEPHON NUMBER AND SYSTEM I.D. # -

PRESS IN SEQUENCE THE FOLLOWING KEYSTROKES:

FUNC 90 * 123 (SECURITY CODE)

PHon WILL DISPLAY

ENTER NEW PHONE NUMBER

XXX XXX XXXX PRESS # PRESS * PHon

_ _ _ _ _ PRESS # PRESS * S id no

PRESS END AT THIS TIME TO EXIT PROGRAMMING MODE.

___________________________________________________________________________

To Re-Initialize Nam Memory for Handset Programmable Models -
Func 99*
Enter Last 8 digits of S.N.
Press *



Programming Instructions for:

PANASONIC EB362


Charged Battery and Nam Adaptor(Grey Cord w/25pin Connector)are needed.

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
THIS FUNCTION IS PROVIDED FOR IN THE PROGRAMMING SEQUENCE



*0000# to enter program mode

*1 Press SND

50 Press SND NAM 1 MODE

_ _ _ _ _ Press STO 01 SIDH

XXXXXXXXXX Press STO 02 OWNDL

1 2 3 Press STO 03 LOCK

0 0 0 0 0 0 0 0 0 0 0 0 (12) Press STO 04 SPDL

00 Press STO 05 SCM

334 Press STO 06 IPCH

07 Press STO 07 ACCOLC

10 Press STO 08 GIM

1 1 0 1 1 1 0 0 Press STO 09 FEATURE A

0 0 0 0 0 1 0 0 Press STO 10 FEATURE B

1 0 0 0 0 0 1 1 Press STO 11 FEATURE C

00 Press STO 12 DLMT

STO **
Turn power off



Programming Instructions for:

PANASONIC EB-500 OR TP-500

ACTION TO STORE DISPLAY

USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
THIS FUNCTION IS PROVIDED FOR IN THE PROGRAMMING SEQUENCE

Attach Nam Programmer Cable (Our Stock # 823)

Pwr up unit

Enter *0000# 0

*1 SND
You are now in the NAM 1 Program mode.

_ _ _ _ _ Press STO 01 S.I.D.

XXXXXXXXXX Press STO 02 OWN #

0 Press STO 03 O for W/L system

334 Press STO 04 IPCH

07 Press STO 05 ACCOLC

10 Press STO 06 GIM

00 Press STO 07 Digit Dial Limit

08 Press STO 08 SCM (3watt i.d.)

911 Press STO 09 Rcl 00

1234 Press STO 10 Security Code

11000000 Press STO 11 FUNCTION BYTE 1

00010010 Press STO 12 FUNCTION BYTE 2

10010111 Press STO 13 FUNCTION BYTE 3

TO BURN NAM AT THIS TIME Press STO ** NAM is burned

Turn off unit
Detach programming cable



Programming Instructions for:

RADIO SHACK 17-1002 TRANSPORTABLE

THIS UNIT REQUIRES A SERVICE HANDSET TO BE PROGRAMMED!!!

A Mobira Service Handset (Modified) may be used. It is made from an ME53
or ME57 handset by opening and adding a jumper to the left of the one
factory installed just below the white 24 pin connector joining the top and
bottom PCB's. Also, pins 1 and 14 of the handset connector must be jumpered
at the radio end. To disassemble the handset, carefully pry off the
plastic earpad retaining housing to expose on hexdrive screw. Two other
screws are under the rubber plugs at either side of the microphone. The
handset then splits apart. This is a ticklish job and isn't recommended
except in an extreme case and not with the customer's handset. The
modification does not affect normal operation of the handset. It is not
known if a Radio Shack handset will work the same.

After the Service Handset has been applied -

To enter LOCAL MODE (which takes the phone off the air and allows service
commands to be obeyed) press 01#. The display should clear and noise is
heard from the earpiece.

To enter the NAM programming mode, enter 48#. The display shows 48 briefly
and clears.

ACTION TO STORE DISPLAY

0 _ _ _ _ _ PRESS * (5 Digit SID)

1 1 PRESS *

2 1 PRESS *

3 XXXXXXXXXX PRESS *

4 10 PRESS *

5 334 PRESS *

6 07 PRESS *

7 0 PRESS *

8 10 PRESS *

9 12345 PRESS *

Press * to exit NAM Programming Mode and return to Local Mode.

To enter the NAM reading Mode, press 49#. The display will show 49



Programming Instructions for:

RADIO SHACK 17-1003 TRANSPORTABLE

*17*1003* To enter program mode. If screen does not clear, enter 1234*

Screen



Programming Instructions for:

UNIDEN CP- 900 THRU 5000 SERIES MOBILES AND TRANSPORTABLES

THIS UNIT REQUIRES A PROGRAMMING HANDSET (MODEL CP-210 DIAGNOSTIC)

Make sure the unit is properly connected to a 13.8 volt supply (cig
lighter) and power on after utility handset is attached.

Upon connecting utility handset to phone, the display will show 1 on the
upper line and OP in the middle.

You are now in the TEST MODE!

Press SELECT, 2, SEND Top will show 2 0 and Current S.I.D.

You are now in the PROGRAM MODE

ACTION TO STORE DISPLAY

0 _ _ _ _ _ PRESS STORE SID

1 1 PRESS STORE LOCAL USE

2 1 PRESS STORE ACCES METH (MIN MARK)

3 XXXXXXXXXX PRESS STORE MIN

4 0334 PRESS STORE INITIAL PAGING CH

5 07 PRESS STORE ACCESS OVERLOAD

6 0 PRESS STORE PREF SYS (O-B,1-A)

7 10 PRESS STORE GROUP I.D. MARK

8 1234 PRESS STORE LOCK CODE (SEE re:)

9 1 PRESS STORE DTMF DURATION

A 0 PRESS STORE AUTO SHUT-OFF

Enter the data for the selected item. If an error is made during data
entry the CLR key can be used to erase single keys.

PRESS SEND to burn NAM. Phone will display PASS. If FAIL is displayed
you must repeat programming sequence.

To read the NAM (review) press SELECT 3 SEND. Enter RCL then the number
of the item that you wish to view. Press the CLR key to exit and return
to test mode.

TO VIEW THE SERIAL NUMBER OF THE UNIT BEING PROGRAMMED -

Press SELECT 4 SEND while in the Test Mode to display the phone's serial
number in decimal form. The manufacturer ID (172) will be displayed on
the top line while the remainder of the serial number will appear on the
bottom line Press the CLR key to return to the Test Mode display.

-------------------------------------------------------------------------------

DEFINITIONS:

XXX - Area Code or Prefix

XXXXXXX - Prefix & Suffix

XXXXXXXXXX - Area Code, Prefix, & Suffix

_ _ _ _ _ - Digits (One Line Per Digit [Sample To Left Is 5 Digits])

MIN* (Mobile Identification Number):
10 digit directory telephone number.

UNLOCK (Lock Code):
3 digit code to unlock radio (WARNING - The radio cannot
be unlocked if this code is forgotten).
NOTE: You can read this code by using the programming procedure.

SID* (Home System Identification):
5 digit number for assigned cellular system.

LU* (Local Use):
0 or 1. 1=local control option and responds to local control messages.

MIN MARK* 0 or 1. 1=home station sends extended address information
upon origination and page response.

IPCH* (Initial Paging Channel in Home):
3 digit number to identify the channel number of the first
paging channel when station is home.

ACCOLC* (Access Overload Class):
2 digit number to identify which overload class field controls
the access attempts.

PS* (Perferred System):
0 or 1. 1=Preferred system is System A
0=Preferred system is System B

GIM* (Group Identification Mark):
2 digit number which indicates how many bits of SID, starting
with the most significant, comprise the GIM.

AUX 0 or 1. 1=Auxiliary signal is enabled for horn relay.
External adapter must be used for this feature.

HANDS 0 or 1. 1=Handsfree feature is enabled.
External adapter must be used for this feature.

ALT LOCK (Alternate Lock Code):
3 digit lock code to be used with the partial lock feature.
This feature is active only with the GE CF-2000 and CF-2500
Carfone models.
This entry is ignored for GE CF-1000 Carfone models.

*These values are Cellular System dependent. Entering an
incorrect value will deny service on the system.

* * * * * * * * * * * * * * * W A R N I N G * * * * * * * * * * * * * * * * * *

When a cellular phone transmits, it sends its Electronic
Identification Number and its assigned telephone number
back to the cellular phone companys computer. This leaves
an electronic trail. If the phone is registered to you and
you change the phone number you run a risk of being tracked
by the Electronic Identification Number.

If the phone is not registered to you, you can be tracked by
the numbers you call frequently. It wouldn't be very smart to
phone home to see how the little woman is doing or check to
see if the latest software came on UPS. And remember, when
you use a cellular phone it goes out over the airways. This
means anyone with the know-how can listen to you. All some
people need is a juicy bit of information and a phone number
and you leave yourself open to all kinds of scams, blackmail,
and legal problems.



* * * M O R E * N O T E S * * *

Most cellular companys do not turn off the numbers that are not
in use. Better yet I do not know of a company that tracks numbers
that are not assigned. They seem to keep the low numbers filled
in. When someone turns in a phone they reassign that number
instead of a new number. If you put a number in your phone, use
a high number. Chances are it is not assigned to anyone. The
calls you make on a unassigned number usually will go unnoticed.
Better yet monitor the number you wish to use with a scanner for
a period of time to check for activity.

Happy foning.....
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
NETWORK 23 BBS, 24 HOURS, 1200/2400 BAUD, (402) 467-2474
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
 
To the best of our knowledge, the text on this page may be freely reproduced and distributed.
If you have any questions about this, please check out our Copyright Policy.

 

totse.com certificate signatures
 
 
About | Advertise | Bad Ideas | Community | Contact Us | Copyright Policy | Drugs | Ego | Erotica
FAQ | Fringe | Link to totse.com | Search | Society | Submissions | Technology
Hot Topics
Php
Withstanding an EMP
Good computer destroyer?
Wow, I never thought the navy would be so obvious.
Alternatives Internets to HTTP
Anti-Virus
a way to monitor someones AIM conversation
VERY simple question: browser history
 
Sponsored Links
 
Ads presented by the
AdBrite Ad Network

 

TSHIRT HELL T-SHIRTS